HG-KR13J+MR-J4-10A 0.8A 100W 0.32NM 3000RPM OIL SEAL AC SERVO MOTOR DRIVE KIT WITH 3M CABLE NEW

HG-MR13J+MR-J4-10A 0.9A 100W 0.32NM 3000RPM OIL SEAL AC SERVO MOTOR DRIVE KIT WITH 3M CABLE NEW

Giá:

HG-MR13J+MR-J4-10A 0.9A 100W 0.32NM 3000RPM OIL SEAL AC SERVO MOTOR DRIVE KIT WITH 3M CABLE NEW

Mô tả sản phẩm

HG-MR13J+MR-J4-10A 0.9A 100W 0.32NM 3000RPM OIL SEAL AC SERVO MOTOR DRIVE KIT WITH 3M CABLE NEW

HG-MR13J+MR-J4-10A 0.9A 100W 0.32NM 3000RPM OIL SEAL AC SERVO MOTOR DRIVE KIT WITH 3M CABLE NEW

MOTOR SPECIFICATIONS:

SERVO MOTOR MODEL HG-MR_ 053(B) 13(B) 23(B) 43(B) 73(B)
POWER FACILITY CAPACITY [KVA] 0.3 0.3 0.5 0.9 1.3
CONTINUOUS RUNNING DUTY RATED OUTPUT [KW] 0.05 0.1 0.2 0.4 0.75
RATED TORQUE [NM] 0.16 0.32 0.64 1.3 2.4
MAXIMUM TORQUE [NM] 0.48 0.95 1.9 3.8 7.2
RATED ROTATION SPEED [RPM] 3000 3000 3000 3000 3000
MAXIMUM ROTATION SPEED [RPM] 6000 6000 6000 6000 6000
PERMISSIBLE INSTANTANEOUS ROTATION SPEED 6900 6900 6900 6900 6900
RATED CURRENT [A] 1.0 0.9 1.5 2.6 5.8
MAXIMUM CURRENT [A] 3.1 2.5 5.3 9.0 20.0
WEIGHT [KG] 0.34 0.54 0.91 1.4 2.8
WEIGHT [KG]( WITH ELECTROMAGNETIC BRAKE) 0.54 0.74 1.3 1.8 3.8

DRIVE SPECIFICATIONS:

MODE NAME MR-J4-10A
STOCKED ITEM S
OUTPUT RATED VOLTAGE 3-PHASE 170 VAC
RATED CURRENT (A) 1.1
MAIN CIRCUIT

POWER

SUPPLY

VOLTAGE/FREQUENCY 3-PHASE OR 1-PHASE 200 VAC TO 240 VAC, 50/60 HZ
RATED CURRENT (A) 0.9
PERMISSIBLE VOLTAGE FLUCTUATION 3-PHASE OR 1-PHASE 170 VAC TO 264 VAC
PERMISSIBLE FREQUENCY FLUCTUATION ±5% MAXIMUM
CONTROL

CIRCUIT

POWER

SUPPLY

VOLTAGE/FREQUENCY 1-PHASE 200 VAC TO 240 VAC, 50/60 HZ
RATED CURRENT (A) 0.2
PERMISSIBLE VOLTAGE FLUCTUATION 1-PHASE 170 VAC TO 264 VAC
PERMISSIBLE FREQUENCY FLUCTUATION ±5% MAXIMUM
POWER CONSUMPTION (W) 30
INTERFACE POWER SUPPLY 24 VDC ±10% (REQUIRED CURRENT CAPACITY: 0.5 A (INCLUDING CN8 CONNECTOR SIGNAL))
LOAD-SIDE ENCODER INTERFACE MITSUBISHI HIGH-SPEED SERIAL COMMUNICATION
TOLERABLE REGENERATIVE POWER OF THE BUILT-IN REGENERATIVE RESISTOR(W)
CONTROL METHOD SINE-WAVE PWM CONTROL/CURRENT CONTROL METHOD
DYNAMIC BRAKE BUILT-IN
PROTECTIVE FUNCTIONS OVERCURRENT SHUT-OFF, REGENERATIVE OVERVOLTAGE SHUT-OFF, OVERLOAD SHUT-OFF (ELECTRONIC THERMAL), SERVO MOTOR OVERHEAT PROTECTION, ENCODER ERROR PROTECTION, REGENERATIVE ERROR PROTECTION, UNDER-VOLTAGE PROTECTION, INSTANTANEOUS POWER FAILURE PROTECTION, OVER-SPEED PROTECTION, ERROR EXCESSIVE PROTECTION, MAGNETIC POLE DETECTION PROTECTION, LINEAR SERVO CONTROL FAULT PROTECTION
POSITION

CONTROL

MODE

MAXIMUM INPUT PULSE FREQUENCY 4 MPPS (WHEN USING DIFFERENTIAL RECEIVER), 200 KPPS (WHEN USING OPEN-COLLECTOR)
POSITIONING FEEDBACK PULSE ENCODER RESOLUTION: 22 BITS
COMMAND PULSE MULTIPLYING FACTOR ELECTRONIC GEAR A/B MULTIPLE, A: 1 TO 16777216, B: 1 TO 16777216, 1/10 < A/B < 4000
POSITIONING COMPLETE WIDTH SETTING 0 PULSE TO ±65535 PULSES (COMMAND PULSE UNIT)
ERROR EXCESSIVE ±3 ROTATIONS
TORQUE LIMIT SET BY PARAMETERS OR EXTERNAL ANALOG INPUT (0 V DC TO +10 V DC/MAXIMUM TORQUE)
SPEED

CONTROL

MODE

SPEED CONTROL RANGE ANALOG SPEED COMMAND 1:2000, INTERNAL SPEED COMMAND 1:5000
ANALOG SPEED COMMAND INPUT 0 V DC TO ±10 V DC/RATED SPEED (SPEED AT 10 V IS CHANGEABLE WITH
SPEED FLUCTUATION RATE ±0.01% MAXIMUM (LOAD FLUCTUATION 0% TO 100%), 0% (POWER FLUCTUATION: ±10%)

±0.2%MAXIMUM(AMBIENT TEMPERATURE 25 ± 10CENTIGRADE DEGREE) ONLY WHEN USING ANALOG SPEED COMMAND

TORQUE LIMIT SET BY PARAMETERS OR EXTERNAL ANALOG INPUT (0 V DC TO +10 V DC/MAXIMUM TORQUE)
TORQUE

CONTROL

MODE

ANALOG TORQUE COMMAND INPUT 0 V DC TO ±8 V DC/MAXIMUM TORQUE (INPUT IMPEDANCE: 10 KOHM TO 12 KOHM)
SPEED LIMIT SET BY PARAMETERS OR EXTERNAL ANALOG INPUT (0 V DC TO ± 10 V DC/RATED SPEED)
FULLY CLOSED LOOP CONTROL AVAILABLE IN THE FUTURE
SAFETY FUNCTION STO (IEC/EN 61800-5-2)
COMMUNICATION FUNCTION USB: CONNECT A PERSONAL COMPUTER (MR CONFIGURATOR2 COMPATIBLE)
STRUCTURE (IP RATING) NATURAL COOLING, OPEN (IP20)
CLOSE MOUNTING POSSIBLE
WEIGHT (KG) 0.8

Đánh giá

Chưa có đánh giá nào.

Hãy là người đầu tiên nhận xét “HG-MR13J+MR-J4-10A 0.9A 100W 0.32NM 3000RPM OIL SEAL AC SERVO MOTOR DRIVE KIT WITH 3M CABLE NEW”

Thư điện tử của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *